Obziy AutoHP1 Instructions for DTF Transfers

Parameter Settings

Applying DTF Transfers with an Obziy Heat Press

Designed around Obziy’s built-in presets for reliable, repeatable results.

Use DTF Mode on the Obziy control panel for one-touch operation. The factory preset is optimized for most DTF films and garments.

DTF Pre-Set Parameters:

• Temperature: 305°F (152°C)

• Time: 20 seconds

• Pressure: 110 lb

Step-by-Step Pressing Instructions

1. Position Your Design

For best results, pre-press the garment (T-shirt, hoodie, etc.) for 3–5 seconds to remove moisture and wrinkles. Allow the fabric to cool completely before placing the transfer.

Position the DTF transfer on the garment with the color side facing up and the powder side facing down in direct contact with the fabric.
Typical placement guidelines:

• Adult T-shirt (front): 3–4 inches below the collar

• Youth T-shirt (front): 2–3 inches below the collar

• Back prints: approximately 1 inch lower than front placement

Once positioned, cover the transfer with the included Teflon sheet to protect the platen and ensure even heat distribution.

2. Press

Press the DTF button on the Obziy control panel to activate the pre-set parameters, then press START.

The upper platen will lower automatically, and the timer will begin counting down. Apply even, consistent pressure—the preset 110 lb pressure is designed to ensure full contact without damaging garment fibers.

If adhesion is incomplete, you may re-press using the same settings or switch to Custom Mode to slightly adjust temperature or time as needed.

3. Peel the Film

Follow the instructions specified by your DTF film manufacturer:

• Hot Peel: Peel the carrier film immediately after pressing while the transfer is still hot.

• Cold Peel: Allow the transfer to cool completely before peeling.

If any part of the design lifts, place the film back down, cover with the Teflon sheet, and press again.

4. Final Press (Recommended)

After peeling, cover the design with the Teflon sheet or a single layer of fabric and press again for 15–20 seconds at the same temperature and pressure.

This final press improves adhesion, enhances durability, and creates a smoother, more professional finish suitable for repeated washing and daily wear.

Applying DTF Transfers with an Obziy Heat Press

Designed around Obziy’s built-in presets for reliable, repeatable results.

Use DTF Mode on the Obziy control panel for one-touch operation. The factory preset is optimized for most DTF films and garments.

DTF Pre-Set Parameters:

• Temperature: 305°F (152°C)

• Time: 20 seconds

• Pressure: 110 lb

Step-by-Step Pressing Instructions

1. Position Your Design

For best results, pre-press the garment (T-shirt, hoodie, etc.) for 3–5 seconds to remove moisture and wrinkles. Allow the fabric to cool completely before placing the transfer.

Position the DTF transfer on the garment with the color side facing up and the powder side facing down in direct contact with the fabric.
Typical placement guidelines:

• Adult T-shirt (front): 3–4 inches below the collar

• Youth T-shirt (front): 2–3 inches below the collar

• Back prints: approximately 1 inch lower than front placement

Once positioned, cover the transfer with the included Teflon sheet to protect the platen and ensure even heat distribution.

2. Press

Press the DTF button on the Obziy control panel to activate the pre-set parameters, then press START.

The upper platen will lower automatically, and the timer will begin counting down. Apply even, consistent pressure—the preset 110 lb pressure is designed to ensure full contact without damaging garment fibers.

If adhesion is incomplete, you may re-press using the same settings or switch to Custom Mode to slightly adjust temperature or time as needed.

3. Peel the Film

Follow the instructions specified by your DTF film manufacturer:

• Hot Peel: Peel the carrier film immediately after pressing while the transfer is still hot.

• Cold Peel: Allow the transfer to cool completely before peeling.

If any part of the design lifts, place the film back down, cover with the Teflon sheet, and press again.

4. Final Press (Recommended)

After peeling, cover the design with the Teflon sheet or a single layer of fabric and press again for 15–20 seconds at the same temperature and pressure.

This final press improves adhesion, enhances durability, and creates a smoother, more professional finish suitable for repeated washing and daily wear.

Troubleshooting